Panamax M5400-PM

Panamax M5400-PM

Regulates Voltage, Improves Picture and Sound Quality, Monitors Incoming Line Voltage, and Reduces Cross-Contamination Between Components.

Voltage Regulation

Improve system performance and prolong equipment life by providing a consistent level of optimal power to your equipment.

Improves Picture and Sound Quality

Level 4+ Power Cleaning and Filtration eliminates common symptoms of contaminated power (including loss of detail, pops, hisses, hums and visual artifacts) and allows your A/V equipment to perform up to its full capability.

Monitors Incoming Line Voltage and Provides a Visual Indication of Power Level

Panamax? patent pending AVM circuitry continuously monitors the incoming power as displayed on the digital voltmeter. In case of an undervoltage or an overvoltage, a flashing lightning bolt will be displayed in red in the voltmeter, and power to the connected equipment is automatically turned off if either of these conditions is detected. When voltage returns to a safe level, power to the equipment is automatically reconnected.

Reduces Cross-Contamination Between Components

The M5400-PM is designed to provide noise isolation between five isolated outlet banks including two high current outlets so that any noise created by an A/V component can not contaminate the power going to equipment plugged into another outlet bank.

Panamax M5400-PM Specifications

General
FamilyPM Series
Line Voltage120 (Volts)
BlueBOLT EnabledNo
Power Factor TechnologyNo
Number of Outlets11
Number of Isolated Banks5
Outlet Descriptions
All 11 outlets voltage regulated, filtered, and surge protected.
Banks 1 and 2 are always on
Bank 3 and 4 are switchable from front panel power button or 12V trigger
Bank 5 outlets are high current and switchable from power button or 12V trigger
Rack MountableYes
Rack Ears IncludedYes
Front Panel Meter(s)1 voltmeter (volts in), 1 voltmeter(volts out)/ammeter combo
Front Media Light(s)No
ControlOn/Off control of switched outlets through front panel power button or rear panel DC trigger.
Voltage RegulationRegulation capture range:
100VAC to 136VAC
Output voltage range:
120VAC ? 6 VAC
CompliancecCSAus
USB Charging1 front panel 500mA USB charger. May not recognize all devices. Check manufactures power specifications of USB device.
Low Voltage Trigger12 V, In/Out
AC Power Cord10 ft. detachable
Dimensions17" W x 12.75" D x 3.5" H, (4.1" Including feet)
Weight20 lbs
AC Protection
AC Protection TechnologyVoltage Regulation
Protect or Disconnect
Automatic Voltage Monitoring
L-N, L-G, N-G Protection Modes
Thermal Fusing
Automatic Voltage ShutoffNo
Under-Voltage Shutoff86VAC ? 6V
Over-Voltage Shutoff142 VAC ? 8 VAC
Maximum Current Rating15 (Amps)
Initial Clamping Level200V Peak
Filtration
Filtration TechnologyLiFT
Filtration Rating
Banks 1, 2, 3, 4: 80 db (100 KHz - 2 MHz)
Bank 5, High Current Outlets: 60 db (100 KHz - 2 MHz)
Signal Line Protection
Signal Line Protection2 LAN, 1 Tel, 3 Cable/Satellite
Shipping Info
Length24.1 (Inches)
Width20.1 (Inches)
Height10.4 (Inches)
Weight23.3 (Lbs)
Unit of MeasureEach
UPC050616008150
Master Pack Qty1
Other Specifications
UL1449 Suppression Rating330V
Peak Impulse Current72,000 A
Energy Dissipation2125 Joules
LAN Circuits -Wires Protected8-Wires
LAN Circuits - ConnectorsRJ-45
LAN Circuits - Compatibility10/100bT
LAN Circuits - Clamping Level52V
USB Circuit - Power Delivery500 mA @ 5VDC
USB Circuit - JacksUSB-A
Telco Protection - Wires Protected2-Wire, Pins 4 & 5
Telco Protection - Suppression ModesMetallic & Longitudinal
Telco Protection - Fuseless/Auto-resettingYes
Telco Protection - ConnectorsRJ-11
Telco Protection - Clamping Level260V
Telco Protection - Capacitance30pf (approx.)
Universal Coax Protection - ShieldedYes
Coax Protection - Insertion Loss< 0.5 dB
Coax Protection - HD 1080 i/p ReadyYes
Coax Protection - Frequency Range0 MHz - 2.2 GHz
Coax Protection - ConnectionsFemale "F", Gold Plated
Coax Protection - Clamping Level75V
Coax Protection -BidirectionalYes